Headphone Amplifier with two Headphone Outputs (4.4 mm Pentaconn, unbal. / 6.3 mm Jack, unbal.)
If you have any questions about this article, just contact our customer service.
Info Hotline:
If you can not reach us by phone, just use our contact form:Violectric HPA V202
The HPA V202 is a pure headphone amplifier and a further development of the multiple test winner HPA V200. It offers the incomparable natural and pleasant sound that made its predecessors famous. With its special technology, the HPA V202 not only offers one of the most powerful headphone amplifiers on the market, but also:
- LOW NOISE due to a very small internal amplification. As a result, the amplifier's inherent noise is inaudible.
- HIGH OUTPUT VOLTAGE due to 50 volts internal operating voltage. Therefore best suited for high impedance headphones.
- HIGH OUTPUT POWER due to powerful amplifiers that can deliver far more power than even the most demanding headphones can use. Therefore ideally suited for headphones with low impedances and also magnetostats!
- HIGH DAMPING FACTOR due to lowest output impedance. Therefore ideally suited to drive even the most difficult headphones without interference, with a guarantee of uncompromised frequency response.
The HPA V202 offers:
- 2 stereo inputs, balanced via XLR and unbalanced via Cinch
- Inputs switchable on the front
- +/18 dB pre-gain for optimum matching of the HPA V202 to source and headphones
- Volume control with RK 27 potentiometer
- Large 38 mm all-aluminium knob
- Powerful stereo amplifier
- 2700 mW Pmax into 50 Ohm
- > 18 V RMS into 600 Ohm
- Delayed connection of headphones after power-on
- headphone outputs: 1 x Pentaconn, unsym. / 1 x 6.3 mm jack, unsym.
- Built-in power supply with toroidal transformer
- 22,000 uF filter capacity
Features
The rear line inputs can be selected via a switch on the front. The activated and buffered signal reaches the output stages after the RK 27 volume control, which are a further development of the famous V200 circuits. Connect your headphones to the HPA V202 and enjoy a compact and fantastic sounding headphone amplifier with the vaunted natural, smooth yet precise Violectric sound.
We have a comprehensive selection of Violectric devices available for demonstration in our headphone studio in Berlin-Kreuzberg. We look forward to your visit!
Technical Data
Device | Violectric HPA-V202 (All values ??RMS unweighted, 20 Hz - 20 kHz, pre-gain at 0 dB) |
Input parameters | |
Inputs (stereo): | 1 x XLR balanced, 1 x RCA, unbalanced |
Max. Input Voltage: | + 21dBu |
Input impedance: | 10k ohms |
Headphone Amplifier Parameters | |
Nominal input sensitivity: | +6dBu |
Power Amp Gain: | +8dB |
PRE GAIN: | -18 / -12 / -6 / 0 / +6 / +12 / +18 dBr |
Frequency Response: | 5Hz - 250kHz (-0.5dB) |
Output Impedance: | 0.25 ohms |
Damping factor (load 50 ohms): | 200 |
Dynamics: | > 128 dB (A-wtd) |
Noise: | < -100 dBu (A-wtd) |
THD+N (1kHz/2x10V/100R = 1W): | < -100dB / < 0.001% |
THD+N (1kHz/2x4V/32R = 0.5W): | < -103dB / < 0.0007% |
Crosstalk: | -100dB (1kHz) / -95dB (15kHz) |
Headphone outputs: | 4.4mm Pentaconn, unbal. / 6.3 mm jack, unbal. |
General | |
Supply voltage: | 230VAC / 115VAC max 10VA |
Front, Back: | 5mm / 2.5mm aluminum, black anodized |
Housing: | 4 mm aluminum, black anodized |
Dimensions enclosure: | 170 x 54 x 228 mm (W x H x D) |
Dimensions above all: | 170 x 65 x 252 mm (W x H x D) |